2026-11-03 by Malcolm Fraser

Fabric Sourcing Checklist: 7 Steps I Still Run Before Any Order

If you're sourcing fabric for pajamas, bedding, or dresses, this is the checklist I go through before I send any PO. I've worked on the manufacturing side for 9 years. In that time I've made 7 significant, expensive mistakes that cost roughly $4,200. This checklist has 7 steps. If I'd had it from day one, none of those 7 failures would have happened.

Quick aside: I've noticed a weird cross-section in fabric fiber discussions where people search for "what are fiber rich foods" and end up on textile pages. That's nutrition. Not textiles. But it does hit a nerve—vague terminology is the #1 cause of sourcing errors. Keep that in mind as you read.

Step 1: Confirm Fiber Composition and Brand Authorization

Lenzing isn't just any old viscose. TENCEL™, Modal, EcoVero are branded fibers. To legally use those names, your supplier needs authorization from Lenzing, and the fiber should be traceable to a batch.

I got burned on this in 2019. A supplier swore up and down they were using Lenzing Modal. But when I asked for authorization paperwork or a Lenzing contact, they couldn't produce it. Turned out the shipment was generic viscose. Looked identical. Hand feel? Different story. Cost me $680 to offload that batch.

What to ask for: Lenzing's authorization letter or paperwork, plus fiber batch traceability info.

Step 2: Nail Down the Exact Technical Specs (In Writing)

Here's where it gets specific. If you're sourcing 68mm three strands Lenzing Tencel, understand what the 68mm actually refers to.

Short version: 68mm is the fiber length. Standard cotton-type staple fiber is typically 38mm. 68mm puts you in long-staple territory—usually used for worsted or high-twist spinning, which gives you a stronger, smoother yarn. The three-strand part refers to the yarn construction: three plies twisted together. The benefits of 68mm three strands Lenzing Tencel: higher tenacity, better spinability, and a more premium hand feel.

But here's the catch. Your supplier needs to produce a spec sheet showing fiber length, denier, crimp, and spinning method. If they can't? Don't place the order.

What to ask for: A written spec sheet with parameters that match your end-use requirement—not "close enough."

Step 3: Insist on a Physical Swatch, Not Photos

I ordered 400 linen bed sheets (queen size) in 2021 based on a pretty photo. The photo showed a light grayish-beige with a fine texture. What arrived was yellowish-beige with the texture of burlap sackcloth. $890 wasted, plus a one-week delay.

Photos don't reveal substrate issues. They don't show batch variation. Hand feel swatches help, but what actually works is cutting a large sample from the bulk roll.

What to ask for: A bulk swatch before full production. Not a photo. Not a swatch card. If the supplier won't send a physical sample—walk away.

Step 4: Match Fabric Weight and Width to the Actual End Product

This step varies by product. Be specific about your expectations.

Linen bed sheets queen size: Look for 140-190 gsm and a width of 90-110 inches. If the width is too narrow, you'll be piecing panels. My line in the sand is 105 inches for queen sheets—anything narrower and you're probably piecing. Piecing means problems.

Viscose maxi dress sleeves: Look for 90-120 gsm and a width of 50-58 inches—so you're not scrambling to fit sleeve pieces into a tight marker. Viscose drapes and flows. Too light? The sleeves flutter. Too heavy? They collapse.

Lenzing Modal pajamas: Weight depends on jersey vs. woven. Jersey typically runs 150-200 gsm. Woven runs 90-120 gsm. Modal is about drape and smoothness—the weight has to match the desired fall. Too light reads as cheap. Too heavy loses that silky feel.

Step 5: Test Shrinkage Before You Approve a Sample

A batch of poorly pre-shrunk linen bed sheets got me in 2022. Shrinkage hit 8%. After one wash in a customer's hands, a queen sheet became a twin.

Lenzing Modal has better dimensional stability than standard viscose. But blending and finishing change everything. Even 5% elastane or cotton in a blend shifts the shrinkage profile.

What to ask for: Run a shrinkage test first. Ask your supplier for cold-water wash data—not hot. Test a sample garment, too. Keep the swatch.

Step 6: Check Cutting and Sewing Compatibility

If I had to bet on which step gets skipped most often, it's this one. Especially with viscose maxi dress sleeves.

Viscose has low wet strength. It's also slippery when dry. During production, it stretches, shifts, and won't hold shape. The armhole is where it falls apart: puckered seams, bubbling, uneven placement.

Learned that one on 200 viscose maxi dresses. The factory upped the stitch length and feed rate to hit volume. Result: puckered, bubbly armholes. $320 in rework, plus a delayed delivery.

What to ask for: Confirm the factory has run similar fabrics. Check armhole and side seam behavior at the sample stage—stitch length, feed dog, and tension all need adjusting.

Step 7: Verify MOQ, Lead Time, and Certifications

MOQ and lead time are the obvious asks. Certifications often get checked too. But the problems usually hide when the two get mixed up.

Lenzing fibers go through an authorization process. OEKO-TEX Standard 100 and FSC certifications need to be in place. If your supplier has expired certification on their TENCEL™, you can't use the brand name.

Then there's the MOQ reality check. Sometimes a smaller run makes more sense financially—because someone else is eating part of the MOQ. Other times, a bulk MOQ gets you a much better unit cost. Run both calculations.

What to ask for: Written MOQ, lead time (with buffer), and certification numbers. Verify them yourself on the certifying body's website.

A Few Things I Wish Someone Had Told Me

Align your terminology. Going back to that "what are fiber rich foods" confusion. It's not just a web oddity—it's a real risk. When a supplier says "fiber," they might mean fiber composition, fiber length, or yarn structure. Define everything with specific parameters before you sign the PO.

The lowest quote is usually the most expensive. I'm not dogmatic about this. Sometimes the cheapest option is right. But in fabric sourcing, the lowest quote usually means something in the fiber blend, processing, or finish has been compromised. Lock your performance requirements before you compare prices.

Keep physical samples. Cheapest, easiest thing on this whole list. Half a meter from every batch, labeled with date and supplier. When a dispute comes up two years later, that's your evidence.

Malcolm Fraser

Malcolm Fraser is a knitted and stretch-fabric analyst specializing in jersey, rib, interlock, elastane blends, breathable knits, sportswear, swimwear, and shape-retentive constructions. He uses ISO 13938-1 bursting tests and ISO 5077 dimensional-change results while comparing gauge, GSM, stretch and recovery, bursting strength, spirality, shrinkage, air permeability, opacity, and wet-state stability. His evaluations help product developers and garment technologists match knit structure, finishing route, fit requirements, chlorine or perspiration exposure, and repeat-laundering expectations.